ABB REACT-3.6-TL Product Manual Download Page 20

Page: 20 / 174

- 20 -

000551AG

2 - Characteristics

odels and range of equipment

The pieces of equipment which make up the REACT system to which
this manual is dedicated are:

Single-phase inverter unit:

REACT-UNO-3.6-TL

single-phase, maximum output power 3600W

REACT-UNO-4.6-TL

single-phase, maximum output power 4600W

Main characteristics

• Number of input channels: 2

• Input connectors: quick fit connectors (2 pairs for each channel)

• DC disconnect switch

• Wireless communication through integrated Wi-Fi board

• Management of external loads through four integrated relays

• AC Back-up Output (off grid)

Battery unit:

REACT-BATT-AP1

average battery capacity 2kWh

In the system up to three REACT-BATT-AP1s can be used (maximum
capacity of the system 3x2kWh=6kWh)

Energy meter:

REACT-MTR-1PH

energy meter for single-phase line

REACT-MTR-3PH

energy meter for three-phase line

The choice of the components for the system must be made by a qualified technician who

knows about the installation conditions, the devices that will be installed outside the inverter
and possible integration with an existing system.

REACT

POWER ALARM GFI ESC UP DOWN ENT

REACT-UNO

REACT-B

ATT

REACT

POWER ALARM GFI ESC UP DOWN ENT

REACT-UNO

REACT-B

ATT

REACT-MTR-1PH

INPUT :
110/230 V
50/60 Hz
10 mA max

Скачано

сайта

интернет

магазина

https://axiomplus.com.ua/

Summary of Contents for REACT-3.6-TL















































































































































































Search results

Summary of Contents for REACT-3.6-TL

Reviews:

Brands by name

Popular brands

ABB REACT-3.6-TL, Product Manual

Search results

Summary of Contents for REACT-3.6-TL

Reviews:

Brands by name

Popular brands