manualshive.com logo in svg

ABB REACT-3.6-TL, Product Manual

Share
Download
ABB REACT-3.6-TL Product Manual Download Page 18

- 18 -

000550AG

1 - Introduction and general information

I

mproper or disallowed use 

IT IS STRICTLY FORBIDDEN TO:

• Install the system in such a way that it is exposed to direct sunlight

•  Install  the  equipment  in  environments  with  particular  flammability 

conditions or in environmental conditions (temperature and humidity) 

other than those specified.

• Use the equipment with safety devices which are faulty or disabled.

•  Use  the  equipment  or  parts  of  the  equipment  by  linking  it  to  other 

machines or equipment, unless expressly provided for.

• Modify operating parameters that are not accessible to the operator and/

or parts of the equipment to vary its performance or change its insulation.

• Clean 

the equipment with corrosive products that may attack parts or 

generate electrostatic charges.

•  Use  or  install  the  appliance  or  parts  of  it  without  having  read  and 

understood the contents of the user and maintenance manual.

• Warm or dry rags and clothes on parts at 

temperature. In addition to 

being hazardous, doing so would compromise component ventilation 
and cooling.

For further information on the installation conditions refer to chapter 5 “Installation”

Скачано

 

с

 

сайта

 

интернет

 

магазина

 https://axiomplus.com.ua/

Summary of Contents for REACT-3.6-TL















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands