manualshive.com logo in svg

ABB PCS6000, User Manual

Share
Download
ABB PCS6000 User Manual Download Page 104

OPERATION

PRODUCT

PCS6000

DOCUMENT KIND

User manual

DOCUMENT ID.

3BHS600000 E40

REV.

G

LANG.

en

PAGE

104/114

8.9. Key switch

The key switch is provided with application specific function:

– Start inhibit (OFF to STANDBY)

– Locking of disconnector (GDM) motor supply

Figure 8–5 Key switch 

8.10. Alarm and fault handling

Two protection levels are used in the PCS6000:

– Alarm: does not shut down the PCS6000. A start is possible.

– Fault: always shuts down the PCS6000 by means of a trip. The start is prevented.

8.10.1. Alarm and trip reset

Press the ACKNOWLEDGE ALARM or ACKNOWLEDGE TRIP function key or select the 
appropriate command from remote control to reset all pending alarms and trips.

If an alarm or fault cannot be reset, the original alarm or fault cause might still be present. 
Ensure that the cause is removed and press the ACKNOWLEDGE ALARM or ACKNOWLEDGE 
TRIP function key again.

Faults caused by defects cannot be reset with the ACKNOWLEDGE TRIP function key. 
Elimination of these faults requires troubleshooting by authorized service personnel.

The PCS6000 can only be started if all faults are eliminated.

Summary of Contents for PCS6000



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands