manualshive.com logo in svg

ABB PCS6000, User Manual

Share
Download
ABB PCS6000 User Manual Download Page 102

OPERATION

PRODUCT

PCS6000

DOCUMENT KIND

User manual

DOCUMENT ID.

3BHS600000 E40

REV.

G

LANG.

en

PAGE

102/114

Figure 8–3 DC-link grounding switch in position “not grounded”, LED indication.

8.

Check that the DC-link grounding switch is in position “not grounded”.

9.

Check the LED indication at the converter side to obtain state information.

The 3 yellow LEDs must be off to get the READY TO START CONVERTER status (see 
Fig. 8–1).

The ISOLATOR CLOSED LED does confirm that the converter DC-link is grounded and it 
is safe to work.

The ISOLATOR RELEASED LED confirms that the solenoid coil is released to connect the 
DC-link to ground. If the LED is off, the DC-link is charged and the handle cannot be 
turned towards the grounded position.

10.

(If applicable): Check that the grid grounding isolator is open and the grid 
disconnectors are closed.

IMPORTANT!

Grid disconnectors and grid grounding isolators are not operated by the 

PCS6000 control.

11.

Check that the main circuit breaker is in operating position.

The PCS6000 is now in status OFF and ready to be started via the customer's HMI system.

Summary of Contents for PCS6000



















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands