ABB PCS6000 User Manual Download Page 100

Page: 100 / 114

OPERATION

PRODUCT

PCS6000

DOCUMENT KIND

User manual

DOCUMENT ID.

3BHS600000 E40

REV.

LANG.

PAGE

100/114

Figure 8–2 Flow chart of anti-dew startup sequence (PF2)

Start

End

CCU

< T

Lim1

YES

CCU

< T

Lim2

CCU

< T

Lim1

Control unit

space heater

OFF

Control unit

space heater

Control unit

auxiliary power

Cooling

pump OFF

Cooling

pump ON

Converter cabinet

auxiliary power

Heat exchanger

bypass

Open

Converter cabinet

dew conditions valid

f(T

CCA

, H

CCA

)

Converter is

ready for

start-up

The auxiliary power feeding of the converter is switched ON.

The temperature limit switch (T1) inside the Converter Control Unit

(CCU) monitors the cubicle inside temperature.

– IF the temperature stays below the limit setting, the cubicle

space heater is switched ON.

– IF the temperature stays above the limit setting, the cubicle

space heater is switched OFF, respectively remains

switched OFF.

The combination of the temperature limit switch (T2) and the

humidity limit switch (H1) monitors the dew conditions inside the

converter control unit.

– IF the temperature stays below the limit setting OR the humidity

stays above the limit setting, the feeding of the auxiliary power

to all other components of the Control Unit stays OFF.

– IF the temperature stays above the limit setting AND the

humidity stays below the limit setting, the feeding of the

auxiliary power to all other components of the Control Unit is

switched ON.

After the auxiliary power of the Converter Control Unit is switched
ON the converter control system starts up and is now able to do
the converter control.

The controller is now monitoring the dew conditions of the

Converter Cabinet by a PT100 temperature sensor and a

humidity sensor.

– IF dew conditions are detected:

• Heat exchanger bypass valve gets fully OPEN to minimum

cooling and other things

• Cooling pump is switched ON

– IF dew conditions are not detected:

• Cooling pump is switched OFF, respectively remains

switched OFF

• Feeding of the auxiliary power of all other components is

switched ON.

• Converter will now start-up completely and enters the

converter OFF-mode state.

Summary of Contents for PCS6000



















































































































Search results

Summary of Contents for PCS6000

Reviews:

Brands by name

Popular brands

ABB PCS6000, User Manual

Search results

Summary of Contents for PCS6000

Reviews:

Brands by name

Popular brands