background image

MN1949WEN

General Information   1-1

General Information

1  General Information

LT0245A03EN    Copyright ABB (c) 2012. All rights reserved.

This manual is copyrighted and all rights are reserved. This document or attached software may not,
in whole or in part, be copied or reproduced in any form without the prior written consent of ABB.

ABB makes no representations or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of fitness for any particular purpose. The information in this
document is subject to change without notice. ABB assumes no responsibility for any errors that may
appear in this document.

Mint™  is a registered trademark of Baldor, a member of the ABB group. 
Windows XP, Windows Vista and Windows 7 are registered trademarks of the Microsoft Corporation.
UL and cUL are registered trademarks of Underwriters Laboratories.

ABB Ltd
Motion Control
6 Bristol Distribution Park
Hawkley Drive
Bristol, BS32 0BF
United Kingdom

Telephone: 

+44 1454 850000

Fax: 

+44 1454 859001

E-mail:

[email protected]

Web site:

www.abbmotion.com

See rear cover for other international offices.

1

Summary of Contents for OPT-MF-001





















Reviews: