ABB OmniCore V250XT Page 384 Product Manual Download

Page: 384 / 456

Description

Name

The Module status LED indicates the follow-
ing:

•

No color: AC_IN is missing or
24V_TRUNK is not available.

•

Red, flashing: Performing self test.

•

Red, steady: An error has occurred
and unit is in error state.

•

Green, flashing: Unit is waiting for
24V_SYS and internal communication.

•

Green, steady: Unit is in operational
state. Activating CTRL inputs in this
state will charge DC_OUT.

MODULE STATUS

The EtherCAT Device State LED/RUN LED
displays the actual state of the device state
machine. The run state is as follows:

•

Off: Power unit is in state INIT.

•

Green flashing (slow): Power unit is in
state PRE-OPERATIONAL.

•

Green single flash: Power unit is in
state SAFE-OPERATIONAL.

•

Green steady: Power unit is in state
OPERATIONAL.

•

Green flickering (fast): Power unit is
in state BOOTSTRAP.

ECAT STATUS

Shows the network communication speed.

•

Green steady: Speed is 100 Mbps.

•

Off: Speed is 10 Mbps.

SPEED

Shows the Link activity of the EtherCAT slave
port 1.

•

Off: No link

•

Yellow flashing: Link and activity.

•

Yellow steady: Link without activity.

LINK/ACT

Shows the network communication speed.

•

Green steady: Speed is 100 Mbps.

•

Off: Speed is 10 Mbps.

SPEED

Shows the Link activity of the EtherCAT slave
port 0.

•

Off: No link

•

Yellow flashing: Link and activity.

•

Yellow steady: Link without activity.

LINK/ACT

Required test equipment

Equipment needed for troubleshooting:

Note

Equipment

Multimeter

Insulating gloves

3HAC074000-008

Circuit diagram - OmniCore V250XT

Continues on next page

384

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

7 Troubleshooting

7.3.4 Troubleshooting the power unit

Continued

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands