ABB OmniCore V250XT Product Manual Download

Page: 171 / 456

4.5.6 Function test of external emergency stop

Overview

Perform this test on the external emergency stop device.

Performing the function test

Note

Action

If any damage is found on the external
emergency stop device or the connection
harness, it must be replaced.

Make a visual inspection of the external
emergency stop device and the connection
harness to make sure they are not physic-
ally damaged.

Pull and rotate the button on the external
emergency stop device clockwise to verify
that it is not pressed in.

Note

If the external emergency stop device is
not controlled by a push-button, make sure
to verify that it is not activated.

Start the robot system.

The test is passed if the event message

10013 Emergency stop state

appears in

the event log.

Note

For collaborative robots, the event mes-
sage

90518 Safety controller Emergency

stop triggered

appears by default. The

message

10013 Emergency stop state

also available in the event log.

Press the emergency stop device.

Note

If the event message

20223 Emergency

stop conflict

appears in the event log, or

the event message

10013 Emergency stop

state

(and

90518 Safety controller Emer-

gency stop triggered

for collaborative ro-

bots) does not appear, then the test has
failed and the root cause of the failure must
be found.

Release the external emergency stop
device to reset the external emergency stop
state.

Product manual - OmniCore V250XT

171

3HAC073447-001 Revision: B

4 Maintenance

4.5.6 Function test of external emergency stop

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands