ABB OmniCore V250XT Product Manual Download

Page: 166 / 456

4.5 Function tests

4.5.1 Function test of emergency stop

Overview

Validate the function of the FlexPendant emergency stop device.

Note

Also perform the test for any additional emergency stop devices.

Performing the function test

Note

Action

If any damage is found on the emergency
stop device, it must be replaced.

Make a visual inspection of the emergency
stop device to make sure it is not physically
damaged.

Pull and rotate the emergency stop device
clockwise to verify that it is not pressed in.

Power on the robot.

The test is passed if the event message

10013 Emergency stop state

appears in

the event log.

Note

For collaborative robots, the event mes-
sage

90518 Safety controller Emergency

stop triggered

appears by default. The

message

10013 Emergency stop state

also available in the event log.

Press the emergency stop device on the
FlexPendant.

Note

If the event message

20223 Emergency

stop conflict

appears in the event log, or

the event message

10013 Emergency stop

state

(and

90518 Safety controller Emer-

gency stop triggered

for collaborative ro-

bots) does not appear, then the test has
failed and the root cause of the failure must
be found.

Release the emergency stop device to re-
set the emergency stop state.

166

Product manual - OmniCore V250XT

3HAC073447-001 Revision: B

4 Maintenance

4.5.1 Function test of emergency stop

Summary of Contents for OmniCore V250XT








































































































































































































































































































































































































































































Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands

ABB OmniCore V250XT, Product Manual

Search results

Summary of Contents for OmniCore V250XT

Reviews:

Related manuals for OmniCore V250XT

Brands by name

Popular brands