manualshive.com logo in svg

ABB OmniCore S Series, Operating Manual

Share
Download
ABB OmniCore S Series Operating Manual Download Page 193

7.2.4 Returning the robot to the path

About paths and return regions

While a program is running, the robot or additional axis is considered to be

on

path

, which means that it follows the desired sequence of positions.

If you stop the program the robot is still on path, unless you change its position.
It is then considered to be

off path

. If the robot is stopped by an emergency or

safety stop it may also be off path.

If the stopped robot is within the

path return region

you can start the program again,

and the robot will return to the path and continue program execution.

Note that there is no way to predict the exact return movement for the robot.

Tip

The path return region is set with system parameters, see

Technical reference

manual - System parameters

,

Type Path Return Region

.

Returning to path

Turning off the power to the robot motors often results in the robot slipping from
its programmed path. This may occur after an uncontrolled emergency or safety
stop. The allowed slip distance is configured with system parameters. The distance
can be different depending on operating mode.

Note

On YuMi robots with SafeMove, axes 5 and 6 can drop slightly when releasing
the enabling device, because there are no brakes on these axes. There is a risk
that mounted tools or workpieces are damaged.

If the robot is not within the configured allowed distance, you may choose to let
the robot return to the programmed path or continue to the next programmed point
in the path. Then the program execution continues automatically in programmed
speed.

1 Make sure there are no obstacles blocking the way and that payload and

work objects are properly placed.

2 If necessary, put the system in automatic mode and press the Motors on

button on the controller to activate the robot motors.

3 Press the Start button on the FlexPendant to continue execution from where

it stopped. One of these things will happen:

•

The robot or axis slowly returns to the path and the execution continues.

•

The

Regain Request

dialog will be displayed.

4 If the

Regain Request

dialog is displayed, select the proper action.

•

Tap

Yes

to return to the path and continue the program.

•

Tap

No

to return to the next target position and continue the program.

•

Tap

Cancel

to cancel the program.

Operating manual - OmniCore

193

3HAC065036-001 Revision: E

© Copyright 20192020 ABB. All rights reserved.

7 Running in production

7.2.4 Returning the robot to the path

Summary of Contents for OmniCore S Series













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands