ABB OmniCore S Series Operating Manual Download Page 126

Page: 126 / 236

How to proceed with tool frame definition

This procedure describes how to define the tool center point in Cartesian
coordinates.

en0400000906

1 Jog the robot to an appropriate position, A, for the first approach point.

Use small increments to accurately position the tool tip as close to the
reference point as possible.

2 Tap

Modify

to define the point.

3 Repeat step 1 and 2 for each approach point to be defined, positions B, C,

and D.

Jog away from the fixed world point to achieve the best result. Just changing
the tool orientation will not give as good a result.

4 If the method you are using is TCP&Z or TCP&Z,X orientation must be defined

as well.

Follow the instructions in

How to define elongator points on page 127

5 If, for some reason, you want to redo the calibration procedure described in

step 1-4, tap

Cancel

Continues on next page

126

Operating manual - OmniCore

3HAC065036-001 Revision: E

6 Programming and testing

6.6.5 Defining the tool frame

Continued

Summary of Contents for OmniCore S Series












































































































































































































































Search results

Summary of Contents for OmniCore S Series

Reviews:

Brands by name

Popular brands

ABB OmniCore S Series, Operating Manual

Search results

Summary of Contents for OmniCore S Series

Reviews:

Brands by name

Popular brands