ABB MultiMove Applications Manual Download

Page: 7 / 110

Overview

3HAC021272-001 Revision: H

ght

200

4-2008 ABB.

Overview

About this manual

This manual contains information about the RobotWare options MultiMove Independent and

MultiMove Coordinated. The latter includes some extended functionality. Unless something

else is specified, MultiMove refers to both these options.

Usage

This manual can be used either as a brief description to find out if MultiMove is the right

choice for solving a problem, or as a description of how to use it. This manual provides

information about system parameters and RAPID components related to MultiMove, and

many examples of how to use them. The details regarding syntax for RAPID components, and

similar, are not described here, but can be found in the respective reference manual.

Who should read this manual?

This manual is mainly intended for robot programmers.

Prerequisites

The reader should...

•

be familiar with industrial robots and their terminology

•

be familiar with the RAPID programming language

•

be familiar with system parameters and how to configure them

•

be familiar with the option Multitasking (see

Application manual - Engineering tools

Organization of chapters

The manual is organized in the following chapters:

References

Chapter

Contents

An introduction to what MultiMove is and how it can be used.

Installation information.

System parameters and how to configure a MultiMove System.

Coordinate systems and how to calibrate them.

The MultiMove user interface on the FlexPendant.

RAPID components and how to write program code for MultiMove.

Error handling for MultiMove, including asynchronously raised errors.

Disconnecting a drive unit and continue working

Reference

Document Id

Technical reference manual - RAPID overview

3HAC16580-1

Technical reference manual - RAPID Instructions, Functions and
Data types

3HAC16581-1

Technical reference manual - RAPID kernel

3HAC16585-1

Operating manual - IRC5 with FlexPendant

3HAC16590-1

Continues on next page

Summary of Contents for MultiMove





































































































Search results

Summary of Contents for MultiMove

Reviews:

Related manuals for MultiMove

Brands by name

Popular brands

ABB MultiMove, Applications Manual

Search results

Summary of Contents for MultiMove

Reviews:

Related manuals for MultiMove

Brands by name

Popular brands