manualshive.com logo in svg

ABB IRC5 with FlexPendant, Operating Manual

Share
Download
ABB IRC5 with FlexPendant Operating Manual Download Page 130

4.4 Restrictions to jogging

Jog additional axes

Additional axes can only be jogged axis-by-axis. Please see

Application

manual - Additional axes and stand alone controller

.

Jog mechanical units that are not calibrated

If the mechanical unit is not calibrated the text

Unit not calibrated

will be displayed

in the

Position

area of the

Jogging

window.

An uncalibrated mechanical unit can only be jogged axis-by-axis. Its working range
will not be checked.

When the robot is not calibrated, incremental movement is restricted to one step
per joystick deflection. A calibrated robot performs 10 steps/sec when deflecting
the joystick.

CAUTION

Mechanical units whose working range is not controlled by the robot system can
be moved to dangerous positions. Mechanical stops should be used and
configured to avoid danger to equipment or personnel.

Jog robot axes in independent mode

It is not possible to jog axes in independent mode. You need to return the axes to
normal mode in order to jog. Please see

Application manual - Controller software

IRC5

for details.

Jog while using world zones

With the option

World Zones

installed, defined zones will restrict motion while you

jog. Please see

Application manual - Controller software IRC5

for details.

Jog with axis loads not set

If equipment is mounted on any of the robot axes, then axes loads must be set.
Otherwise overload errors might occur when jogging.

How to set axis loads are described in the Product Manuals delivered with your
robot.

Jog with tool or payload weights not set

If the weight of tools and payloads is not set, then overload errors might occur
when jogging. Loads for additional axes controlled by specific software (dynamic
models) can only be set in programing.

130

Operating manual - IRC5 with FlexPendant

3HAC050941-001 Revision: G

© Copyright 2018 ABB. All rights reserved.

4 Jogging

4.4 Restrictions to jogging

Summary of Contents for IRC5 with FlexPendant



















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands