ABB IRB 920 Product Manual Download Page 421

Page: 421 / 1008

5.6.2 Replacing the bellows

Location of the bellows

The bellows are located as shown in the figure.

xx2100002397

Required spare parts

Note

The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 920 via myABB Business Portal,

www.abb.com/myABB

Note

Article number

Spare part

Used with protection type Clean
Room.

3HAC073494-001

Bellow 140

Used with protection type Clean
Room.

3HAC073495-001

Below, Long stroke

Replace if damaged.

3HAC071547-001

Bellow Gasket

Replace if damaged.

3HAC073487-001

Top Cover

Replace if damaged.

3HAC073491-001

Lower Cover

Replace if damaged.

3HAC073489-001

Extension shaft

Replace if damaged.

3HAC073492-001

Extension shaft, Long stroke

Used with protection class IP54.

3HAC066658-001

Gasket

Replace if damaged.

3HAC073490-001

Shaft

Continues on next page

Product manual - IRB 920

421

3HAC075721-001 Revision: C

5 Repair

5.6.2 Replacing the bellows

Summary of Contents for IRB 920

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for IRB 920

Reviews:

Brands by name

Popular brands

ABB IRB 920, Product Manual

Search results

Summary of Contents for IRB 920

Reviews:

Brands by name

Popular brands