ABB IRB 390 Product Manual Download | Manualshive

Page: 310 / 346

background image

6.4.3 Installation locations for the calibration tools

Location of fixed calibration items

This section shows how the robot is equipped with items for installation of
calibration tools for Axis Calibration (fixed calibration pins and/or bushings).
Installed calibration tools are not shown.

A fixed calibration pin and a bushing for the movable calibration tool are located
on each axis as follows.

If there is not enough space on an axis to install a fixed calibration pin, the axis is
equipped with two bushings instead, for installation of two calibration tools when
calibration is carried out. This is shown in the figure.

xx2000000025

Continues on next page

310

Product manual - IRB 390

3HAC066566-001 Revision: B

© Copyright 2020 - 2021 ABB. All rights reserved.

6 Calibration

6.4.3 Installation locations for the calibration tools

«
...
308
309
310
311
312
...
»

Summary of Contents for IRB 390



























































































































































































































































































































































Reviews:

No comments

Related manuals for IRB 390

Brand: Makeblock Pages: 57

Jimu Robot Series

Brand: UBTECH Pages: 28

Mi Robot Builder Rover

Brand: Xiaomi Pages: 8

Recon Scout OCU02

Brand: ReconRobotics Pages: 12

Brand: K-Team Pages: 53

Brand: Epson Pages: 84

Brand: Epson Pages: 274

Brand: Epson Pages: 112

ProSix S5 Series

Brand: Epson Pages: 211

Brand: Epson Pages: 122

SCARA GX Series

Brand: Epson Pages: 236

Brand: Epson Pages: 184

Part Feeding 7.0 IF-80

Brand: Epson Pages: 58

Brand: Epson Pages: 64

Brand: Parallax Pages: 18

Brand: STEMLABS Pages: 33

Brand: THINK GIZMOS Pages: 2

Brand: TopXGun Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands