ABB IRB 390 Product Manual Download

Page: 135 / 346

•

Replacing the axis-4 gear unit pre-stage on page 265

•

Replacing the axis-5 gear unit pre-stage on page 281

•

Replacing the cable harness on page 168

•

Replacing the axis-1, axis 2 and axis-3 motor on page 236

Refitting the base unit

Use these procedures to refit the base unit.

Installing the base unit

Use the procedure to install the base unit.

Note

Action

xx1900000210

Fasten three lifting eyes.

CAUTION

The weight of the complete base unit and upper
arms is 136 kg.
All lifting accessories used must be sized accord-
ingly.

Make sure the roundsling has free
space and does not wear against
any part of the robot.

Attach the roundslings to the lifting eyes.

Note

Make sure the roundslings do not rub against any
sharp edges.

WARNING

Personnel must not, under any circumstances,
be present under the suspended load.

Continues on next page

Product manual - IRB 390

135

3HAC066566-001 Revision: B

5 Repair

5.4.1 Replacing the base unit

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands