manualshive.com logo in svg

ABB IRB 1200, Product Manual, Page: 119 / 906

Share
Download
ABB IRB 1200 Product Manual Download Page 119

3.3 Inspection activities

3.3.1 Inspecting the robot paint

General

For robots with protection type Hygienic, there is a risk of surface corrosion or
paint peeling in case of mechanical damage to the coated surface. Therefore, it is
important to regularly inspect robot surfaces for any paint breaking or damage.

Required tools and equipment

Note

Spare parts

Equipment

Lint free cloth

White

3HAC036639-001

Touch up paint Clean Room/Hy-
gienic

Inspection, robot paint

Description

Action

Visually inspect the robot surface paint for
any paint breaking.

1

Use a lint free cloth.

If there is paint breaking, clean the surface
so that it is free from oil and grease.

2

3HAC036639-001

Use Touch up paint Clean Room/Hygienic,
white to paint any damaged surfaces.

Note

Always read the instruction in the product
data sheet in the paint repair kit for Clean
Room/Hygienic.

3

Product manual - IRB 1200

119

3HAC046983-001 Revision: S

© Copyright 2014 - 2021 ABB. All rights reserved.

3 Maintenance

3.3.1 Inspecting the robot paint

Summary of Contents for IRB 1200











































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments