ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 133

Page: 133 / 152

ABB i-bus

KNX

Planning and application

JRA/S 6.230.3.1 | 2CDC506083D0201 131

4.2.3

Connection/logic

With the Logic function it is possible to connect the switching of the output with certain conditions.
Two connection group objects are available:

Initially the

Switch

group object is evaluated by the

Logical connection 1

group object. The result of this is

then connected with the

Logical connection 2

group object.

The following Logic functions are possible:

Communication object values

Explanations

Logical
function

Switch

Logical
connection 1

Output

Logical
connection 2

Output

AND

The result is 1 if both input
values are 1.

The output is 1 if both input
values are 1.

The result is 1 if one of the
input values is 1.

XOR

The result is 1 if the two input
values have a different value.

GATE

closed

open

closed

open

closed

open

closed

open

The

Switch

group object is

only allowed through if the
GATE (connection) is open.
Otherwise receipt of the

Switch

group object is ignored.

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Search results

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

Reviews:

Brands by name

Popular brands

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Search results

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

Reviews:

Brands by name

Popular brands