ABB HT611658 Operation Manual Download

Page: 108 / 148

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.11 Installing the compressor casing

HZTL4033_EN

Rev.K

January 2022

Turning and moving in wall insert

Fig. 62: Turning and moving in wall insert

1. Secure the lifting device (90190 / 90195) and the fixing segment (90192) to the flange of

the wall insert (77000) using the screws (90197) and washers (90198).
Carefully turn wall insert (77000) with fitted diffuser over the support angle (90025) and
pull up vertically.

2. Remove support angle (90025), screws and nuts.

3. Carefully install the wall insert (77000) in the compressor casing. Make sure both mark-

ings are in the correct position.

Page

106

146

Summary of Contents for HT611658



















































































































































Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands

ABB HT611658, Operation Manual

Search results

Summary of Contents for HT611658

Reviews:

Related manuals for HT611658

Brands by name

Popular brands