ABB HT608505 Operation Manual Download Page 34

Page: 34 / 148

Operation Manual / A170-M.. - A175-M..

3 Removal and installation / 3.3 Installing the turbocharger

HZTL4033_EN

Rev.I

November 2021

3.3

Installing the turbocharger

WARNING

Risk of tipping

If the turbocharger is not sufficiently supported or not supported at all dur-
ing removal and installation, it may tip over and cause severe injury to per-
sonnel or accidents resulting in fatalities.

Support the turbocharger at a suitable location.

Secure with lifting gear wherever possible.

Fig. 15: Turbocharger suspension points

If present: Remove insulation segment on the bearing casing.

Attach lifting gear to the suspension lug of the bearing casing and the turbine-end foot.

Remove the covers from the oil connections.

Align turbocharger and place on bracket.

Page

146

Summary of Contents for HT608505



















































































































































Search results

Summary of Contents for HT608505

Reviews:

Brands by name

Popular brands

ABB HT608505, Operation Manual

Search results

Summary of Contents for HT608505

Reviews:

Brands by name

Popular brands