manualshive.com logo in svg

ABB HT600966, Operation Manual

Share
Download
ABB HT600966 Operation Manual Download Page 31

Operation Manual / A170-M.. - A175-M..

3  Removal and installation / 3.2  Removing the turbocharger

© Copyright 2020 ABB. All rights reserved.

HZTL4033_EN

Rev.G

December 2020

3.2

Removing the turbocharger

 WARNING

Risk of tipping

If the turbocharger is not sufficiently supported or not supported at all dur-
ing removal and installation, it may tip over and cause severe injury to per-
sonnel or accidents resulting in fatalities.

u

Support the turbocharger at a suitable location.

u

Secure with lifting gear wherever possible.

u

If present: Loosen cable to speed sensor.

u

Disconnect all gas, air and lubricating oil pipes.

Fig. 12: Turbocharger suspension points

u

If present: Remove insulation segments on bearing casing and feet.

u

Attach lifting gear to the suspension lug of the bearing casing and through the boles on
the turbine-end foot.

Page 

29

 / 

143

Summary of Contents for HT600966



















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands