ABB HT569038 Operation Manual Download | Manualshive

Page: 39 / 122

background image

Operation Manual / 4 Product description / A130-H.. - A140-H

2 Removing and Installing / 2.2 Removing the turbocharger

© Copyright 2017 ABB. All rights reserved.

HZTL4030_EN

Revision D

May 2017

2.2

Removing the turbocharger

u

Disconnect all pipes according to the instructions of the enginebuilder.

u

If present: Loosen and remove the compressor wheel cooling connection. Close the com-
pressor wheel cooling opening with a screw plug (01).

Fig. 6: Removing the turbocharger

A

Position of expansion sleeves

B

Clamping nut

C

Standard nut

u

Apply penetrating oil to thread of stud (02) and nut and let it work in.

u

If present: Disconnect the plug to the speed sensor (86505) and secure the rolled-up
cable on the turbocharger. This protects the plug from being crushed.

u

If present: Detach the support (61301) from the engine support.

Depending on the bracket version (04), two positioning pins (05) can be used for positioning
and safeguarding against wrong fitting of the turbocharger. Therefore the turbocharger
must always be removed from and installed on the bracket vertically.

The gas outlet casing (61001) can remain fitted in the exhaust gas pipe if the locking nuts
are accessible. Otherwise the complete turbocharger unit including gas outlet casing must
be removed.

Page

9

/

91

«
...
37
38
39
40
41
...
»

Summary of Contents for HT569038



























































































































Reviews:

No comments

Related manuals for HT569038

Brand: Kensington Pages: 18

DBU-3200 Series

Brand: Mean Well Pages: 18

EVduty EVC30 Series

Brand: Elmec Pages: 26

Brand: Turbot Pages: 3

Wallbox Home 11 kW

Brand: WINDSY Pages: 31

Brand: WARRIOR Pages: 29

DROP XL Watch Edition

Brand: NATIVE UNION Pages: 17

Brand: GTS Pages: 2

Brand: Jackery Pages: 25

Brand: Jupio Pages: 2

Brand: Uplift Desk Pages: 2

Brand: MicroPower Pages: 185

Brand: Grin Technologies Pages: 21

Brand: DieHard Pages: 12

Brand: DieHard Pages: 16

Brand: DieHard Pages: 16

Brand: DieHard Pages: 16

Brand: DieHard Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands