ABB GOE(2) Installation And Commissioning Manual Download Page 30

Page: 30 / 80

Installation and commissioning guide

1ZSC000563-ACF EN, REV. A, 2020-06-25

Install the winding cables to the bottom contact.

CAUTION!

Make sure that there is no tension in
the winding cables. Tension in the
winding cables will cause damage to
the bottom contact.

G004308

Torque

68 ±6 Nm

Lift the bushing above the opening in the transformer.

Continue with

Installation of the bushing on the transformer,

page

End of instruction

4.5.3 Installation of the large bottom contact in the transformer

Overview

The end-shield can be installed to both the large bottom contact and the bottom nut of the bushing. This
procedure describes installation on the bottom contact. For installation on the bottom nut, refer to

Installation

of the small bottom contact in the transformer,

page

G004296

41 Large bottom contact

Summary of Contents for GOE(2)

















































































Search results

Summary of Contents for GOE(2)

Reviews:

Brands by name

Popular brands

ABB GOE(2), Installation And Commissioning Manual

Search results

Summary of Contents for GOE(2)

Reviews:

Brands by name

Popular brands