ABB GOE(2) Installation And Commissioning Manual Download Page 17

Page: 17 / 80

Installation and commissioning guide
1ZSC000563-ACF EN, REV. A, 2020-06-25

4 Installation

4.1 Tools

Tool

Part number

Note

Lifting tool

9760 668-C

Soft bedding

E.g. rubber mat or wood board

Soft lifting slings

Pull-through cord

9760 669-A

With M8 terminal.

For assembly and disassembly of the
draw rod and draw lead.

Torque wrench key for hexagon head
screws, head width 16 mm (M10) and 13
mm (M8).

Wrench for hexagon head screws 45 mm
or adjustable wrench for 45 mm bolts
or larger.

For the test tap cover.

Shackles

To fit Ø 25 mm holes, for connection of
the soft lifting slings to the bushing
flange.

Hydraulic jack

9769 897-A

For removal, and installation of the
bottom contact. Draw-rod system.

Box spanner

9760 669-B

For removal, and installation of the
bottom contact. Draw-rod system.

Tackle

For installation of the bushing at a
specific angle.

4.2 Consumables

Item

Brand

ABB part
number

Note

Oil based Vaseline

Fuchs

For treatment of contact surfases. Does
not react with transformer oil.

Mobilgrease 28

MOBIL

Lubricates and protects metals against
corrosion. Protects rubber. Does not
react with transformer oil.

Molykote Multilub

Dow Corning

For lubrication of draw-rod threads and
bolts on the outer terminal.

Thread-locking fluid
grade 42

High strength thread-locking fluid,
permanent locking.

Thread-locking activator
grade 47

Activator for thread-locking fluid
grade 42.

Summary of Contents for GOE(2)

















































































Search results

Summary of Contents for GOE(2)

Reviews:

Brands by name

Popular brands

ABB GOE(2), Installation And Commissioning Manual

Search results

Summary of Contents for GOE(2)

Reviews:

Brands by name

Popular brands