manualshive.com logo in svg

ABB FCAN-01, User Manual

Share
Download
ABB FCAN-01 User Manual Download Page 87

Communication profiles   87

7

Communication profiles

What this chapter contains

This chapter describes the communication profiles used in 

communication between the CANopen network, the adapter 

module and the drive.

Communication profiles

Communication profiles are ways of conveying control commands 

(Control word, Status word, references and actual values) between 

the master station and the drive.
With the FCAN-01 CANopen adapter module, the CANopen 

network may employ the CiA 402 profile (Device profile for drives 

and motion control) or the ABB Drives profile. Both are converted 

to the native profile (for example, DCU or FBA, detailed in the drive 

manuals) by the adapter module. In addition, two Transparent 

profiles – for 16-bit and 32-bit words respectively – are available. 

With the Transparent modes, no data conversion takes place.

Note:

 The CiA 402 operation mode support is drive-specific. See 

CANopen device profile CiA 402

 on page 

89

 for more details.

The profile is selected from the drive with parameter 05 PROFILE 

of the fieldbus configuration group A. For example, if parameter 05 

PROFILE is set to 0, the Control word of the drive is set according 

to the CiA 402 specification.

Summary of Contents for FCAN-01

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands