manualshive.com logo in svg

ABB FBIP-21 BACnet/IP, User Manual

Share
Download
ABB FBIP-21 BACnet/IP User Manual Download Page 35

BACnet access point

Description

Drive parameter

AV131

Previous hour energy consump-
tion. The value 01.50 Current hour
kWh is stored here when its values
has been cumulated for 60
minutes. The value is set to the
value before the power cycle when
the drive is again up and running.

01.51 Previous hour kWh

AV132

Current day energy consumption.
The value 01.51 Previous hour kWh
is stored here when its value has
been cumulated for 24 hours. The
value is set to the value before the
power cycle when the drive is
again up and running.

01.52 Current day kWh

AV133

Previous day energy consump-
tion. The value 01.52 Current day
kWh is stored here when its value
has been cumulated for 24 hours.
The value is set to the value be-
fore the power cycle when the
drive is again up and running

01.53 Previous day kWh

￭

Fault queue for drive diagnostics

Faults specific to fieldbus control are listed below:

For general diagnostics information, see the Diagnostics section in the drive firmware
manual.

BACnet access point

Description

Drive parameter

AV18

Fault that caused the current trip

04.01 Tripping fault

AV19

Code of the first stored (non-act-
ive) fault

04.11 Latest fault

AV20

Code of the second stored (non-
active) fault

04.12 2nd last fault

Start-up 35

12

Summary of Contents for FBIP-21 BACnet/IP











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands