ABB DressPack IRB6650S Product Manual Download Page 88 | Manualshive

Page: 88 / 390

ABB DressPack IRB6650S Product Manual Download Page 88

2.2.7 Installation of IRBDP MH2 UE and IRBDP SW2 UE

2.2.7.1 Fitting the attachments of IRBDP MH2 UE and IRBDP SW2 UE

Note

This section is also valid for how to fit the attachments on the upper end of the
cable package IRBDP SW2 CE. Only difference is that the connection plate
between upper and lower cable package does not exist since the harness is
continuous.

Location of the attachments of IRBDP MH2 UE and IRBDP SW2 UE

The location of the attachments of the cable packages IRBDP MH2 UE and SW2
UE is shown in the figure.

Figure shows IRB 7600.

xx0800000154

Gripping clamp (lower arm plate)

A

Process cable package, upper arm

B

Ball joint housing (tension arm unit)

C

Tension arm unit

D

Ball joint housing (process cable support axis 6)

E

Process cable support axis 6, complete

F

Continues on next page

88

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

© Copyright 2004-2018 ABB. All rights reserved.

2 Installation

2.2.7.1 Fitting the attachments of IRBDP MH2 UE and IRBDP SW2 UE

«
...
86
87
88
89
90
...
»

Summary of Contents for DressPack IRB6650S







































































































































































































































































































































































































Reviews:

No comments