ABB DressPack IRB6650S Product Manual Download Page 232

Page: 232 / 390

Location of the cable package IRBDP MH2 LI

The cable package IRBDP MH2 LI is located as shown in the illustration.

xx0500001534

Velcro straps

Lower arm internal cable package

Cable fixing bracket

Connection plate

Lower arm plate

Cable bracket, base frame

Required equipment

The following equipment is required for replacement of the cable packages IRBDP
MH1 LI and MH2 LI.

Note

Equipment

See

Spare Parts

Cable packages IRBDP MH1 LI and MH2 LI

A number of version are available, see

Lower

arm Internal cable package on page 361

The content is described in section

Toolkit,

SpotPack/DressPack

Standard toolkit, DressPack/SpotPack

Continues on next page

232

Product manual - DressPack/SpotPack IRB 6650S

3HAC055424-001 Revision: C

4 Repair

4.2.2 Replacing the cable packages - IRBDP MH1 LI and MH2 LI

Continued

Summary of Contents for DressPack IRB6650S






































































































































































































































































































































































































Search results

Summary of Contents for DressPack IRB6650S

Reviews:

ABB DressPack IRB6650S, Product Manual, Page: 232 / 390

Search results

Summary of Contents for DressPack IRB6650S

Reviews: