ABB DPA UPScale ST40 User Manual Download Page 43

Page: 43 / 129

Modifications reserved

Page 43/79

The ALARM LED indicator is a visual indication of any internal or external alarm condition. At the same

time, an audible alarm will be activated.

INDICATOR

INDICATOR STATUS

MEANING

ALARM

OFF
RED

No alarm condition
Alarm condition

LINE 1

GREEN
RED

Mains rectifier available
Mains rectifier not available

LINE 2

GREEN
RED
OFF

Mains bypass available
Mains bypass not OK or not available
UPS is turned off

BYPASS

GREEN
OFF

Load on bypass (bypass-or eco-mode)
Bypass not operating (switched-off)

INV

GREEN
RED
OFF

Load on inverter
Inverter fault or load not transferable to inverter
Inverter not operating (switched-off)

BATTERY

OFF
GREEN
RED
Flashing GREEN
Flashing RED

UPS is turned off
Battery connected and ok
Fault condition of the battery (alarm)
Battery in discharge
Battery low or disconnected

6.1.2

Buttons

The keys allow the user to perform settings and adjustments, to start up and shut down the UPS and,

using the LCD, to monitor voltages, currents, frequencies and other values.

KEYS

FUNCTION

ON/OFF
ON/OFF

Serves to switch-on (press both keys simultaneously), or shut down the UPS (press both keys

simultaneously)

UP (



)

Move upwards through the menu

DOWN (



)

Move downwards through the menu.

RESET

Cancel the audible alarm. If the alarm condition was only transient the LED-indicator ALARM would also

extinguish otherwise it will remain on (red).

ENTER

Confirms a chosen menu item.

NOTE

IF A PARALLEL UPS HAS TO BE TURNED OFF, THEN BOTH ON/OFF

BUTTONS ON ALL UPS MODULES HAVE TO BE PUSHED. IN THIS CASE,
THE POWER SUPPLY TO THE LOAD WILL BE INTERRUPTED

Summary of Contents for DPA UPScale ST40




























































































































Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Related manuals for DPA UPScale ST40

Brands by name

Popular brands

ABB DPA UPScale ST40, User Manual

Search results

Summary of Contents for DPA UPScale ST40

Reviews:

Related manuals for DPA UPScale ST40

Brands by name

Popular brands