ABB DPA UPScale ST40 User Manual Download Page 34

Page: 34 / 129

Modifications reserved

Page 34/79

5.6

External batteries

WARNING!

KEEP AWAY FROM BATTERY POLES AS THESE CARRY DANGEROUS DC

VOLTAGES THAT CAN CAUSE FATAL ACCIDENTS.

NOTE:

MANIPULATION OF THE BATTERY SYSTEM SHOULD ONLY BE

PERFORMED BY TRAINED SERVICE AND MAINTENANCE PERSONNEL

FROM THE MANUFACTURER OR HIS CERTIFIED SERVICE PARTNERS.

INAPPROPRIATE MANIPULATIONS OF THE BATTERIES CAN CAUSE

SPARKS. WHILE WORKING ON BATTERY SYSTEMS IT IS MANDATORY TO

WEAR PROTECTIVE GLASSES

5.6.1

External battery configuration

In the DPA UPScale

ST 80, ST 120 and ST 200 UPS cabinets there is no space provided for

batteries.

There are two external matching battery cabinets available:

•

CBAT UPScale -120 for Separate or Common battery configurations of 24Ah or 28Ah blocks

(max. 120 Blocks)

•

CBAT UPScale-200 for Separate or Common battery configurations for 24Ah or 28Ah blocks

(max. 200 Blocks)

S-type = For Separate. Battery

C-type = For Common. Battery

CBAT-UPScale-120

S-type or C-type

CBAT-UPScale-200

S-type or C-type

Battery frames

Configuration accommodates:

Max.

120 Batt. block x

24Ah/28Ah

on 8 shelf

3x5=15 blocks/shelf

200 Batt. blocks x

24Ah/28Ah

on 7 shelf

6x5=30 blocks/shelf

Battery fuses / Max. Batt. Strings :

Terminals :

S-type

9 / 3

(Terminal 9 x 16/25mm2)

15 / 5

(Terminal 15 x 16/25mm2)

Battery fuses / Max. Batt. Strings
Terminals :

C-type

9 / 3

+ Com. Connection

Bar

3 x (2xM8) +PE 2xM8

15 / 5

+ Com. Connection

Bar

3 x (2xM10) +PE

2xM10

Fuse Type (Very Fast acting)

3x100 A

5x100A

Dimensions (WxHxD)

730x1975x800

1200x1975x800

Weight with trays and w/o batteries kg

290

410

For detailed information on, and layout of, the battery cabinets please refer to the “external battery

cabinets” chapter in the technical data sheet.

Summary of Contents for DPA UPScale ST40




























































































































Search results

Summary of Contents for DPA UPScale ST40

Reviews:

ABB DPA UPScale ST40, User Manual, Page: 34 / 129

Search results

Summary of Contents for DPA UPScale ST40

Reviews: