ABB AV1 Operating Instructions Manual Download Page 63

Page: 63 / 126

REPAIR AND REPLACEMENT

REPLACEMENT PROCEDURES

8 - 3

Remove the four hinge screws (Item 42) while holding the beam

assembly steady (Item 6). Remove the two screws that connect the
beam to the hinge first.

Remove the gain hinge spring.

Insert the new gain hinge spring.

NOTE:

When installing the gain hinge spring, be sure it properly

seats (flush) between the steps. If the gain hinge spring hangs
up, remove and rotate the hinge 90

. Check for proper seating.

Insert and torque the screws to 2.6,

0.2 Nm (23,

2 in.-lbs) while

holding the beam assembly steady (Item 6). Insert the two screws
that secure the hinge to the housing first.

Transfer the positioner back to automatic operation (

Section 5

Perform the procedure outlined in

PILOT VALVE STROKE

ADJUSTMENT

Pilot Valve Assembly

NOTES:

Refer to

Section 9

for pilot valve assembly kit numbers.

Item numbers in this procedure reference Figure

9-3

9-4

Figure 8-2. Manifold O-Rings

T00781A

O-RINGS

Summary of Contents for AV1































































































































Search results

Summary of Contents for AV1

Reviews:

Related manuals for AV1

Brands by name

Popular brands

ABB AV1, Operating Instructions Manual

Search results

Summary of Contents for AV1

Reviews:

Related manuals for AV1

Brands by name

Popular brands