![background image](http://html1.mh-extra.com/html/abb/acs880-87lc-4000a-4021a-7/acs880-87lc-4000a-4021a-7_hardware-manual_3461597115.webp)
Technical data 115
Applicable standards
CE marking
A CE mark is attached to the converter to verify that the converter follows the provisions of
the European Low Voltage Directive 2014/35/EU (previously 2006/95/EC) and EMC
Directive 2014/30/EU (previously 2004/108/EC).
Compliance with the European Low Voltage Directive
The compliance with the European Low Voltage Directive has been verified according to
standard EN 61800-5-1.
Compliance with the European EMC Directive
Compliance with EN 61800-3:2004/A1:2012
Compliance with the European Machinery Directive
Note:
In standard texts, the term 'drive' stands for 'converter' in case of wind turbine
applications.
The drive is an electronic product which is covered by the European Low Voltage
Directive. The drive is equipped with a main circuit breaker which can be used in safety
functions for machinery. These safety functions are in the scope of the Machinery Directive
as safety components, and appropriate harmonized standards (EN ISO 13849 or
EN 62061) shall be applied.
Converters with the Q951, see
Emergency stop, stop category 0 (Q951)
for ACS880-77LC/87LC wind turbine converters user's manual
(3AXD50000040787
[English]).
The converter complies with the standards below. The compliance with the
European Low Voltage Directive is verified according to standards EN 61800-5-1.
• EN 60204-1: 2006 +
A1:2009 + AC:2010
Safety of machinery. Electrical equipment of machines. Part 1: General
requirements.
Provisions for compliance:
The final assembler of the machine is
responsible for installing
- an emergency-stop device.
• EN 60529:1991
Degrees of protection provided by enclosures (IP code)
• EN/IEC 61439:2011
Low-voltage switchgear and controlgear assemblies
• EN/IEC 60146
Semiconductor converters - General requirements and line commutated
converters
• EN/IEC 50178
Electronic equipment for use in power installations
• IEC 60664-1:2007
Insulation coordination for equipment within low-voltage systems. Part 1:
Principles, requirements and tests.
• IEC 61400-1:2005
Wind turbines. Part 1: Design requirements
• IEC 61800-3:2017
Adjustable speed electrical power drive systems. Part 3: EMC requirements and
specific test methods
• EN 61800-5-1:2007
Adjustable speed electrical power drive systems. Part 5-1: Safety requirements –
electrical, thermal and energy.
• BS7671
Requirements for electrical installations
• NEMA 250:2003
Enclosures for Electrical Equipment (1000 Volts Maximum)
• UL 61800-5-1
Adjustable Speed Electrical Power Drive Systems - Part 5-1: Safety Requirements
- Electrical, Thermal and Energy. See
on page
• GL-IV-1:2010
Guideline for Certification of Wind Turbines
Summary of Contents for ACS880-87LC-4000A/4021A-7
