ABB ACS580-01 drives, Hardware Manual

Page: 59 / 226

Planning the electrical installation 59

Typical power cable sizes
The table below gives copper cable types with concentric copper shield for the drives
with nominal current. The value separated by the plus sign means the diameter of the
PE conductor.
See also section Terminal and lead-through data for the power cables on page 147 .
Drive type
ACSH580
Frame
size
IEC
1)
US
Cu cable type AI cable type
2)
Cu cable type AI cable type
3)
mm
2
mm
2
AWG/kcmil AWG/kcmil
3-phase U
N
= 400 V (380…480 V)
01-02A6-4 R0 3×1.5 + 1.5 - 16 -
01-03A3-4 R0 3×1.5 + 1.5 - 16 -
01-04A0-4 R0 3×1.5 + 1.5 - 16 -
01-05A6-4 R0 3×1.5 + 1.5 - 16 -
01-07A2-4 R1 3×1.5 + 1.5 - 16 -
01-09A4-4 R1 3×2.5 + 2.5 - 14 -
01-12A6-4 R1 3×2.5 + 2.5 - 14 -
01-017A-4 R2 3×2.5 + 2.5 - 14 -
01-025A-4 R2 3×6 + 6 - 10 -
01-032A-4 R3 3×10 + 10 - 8 -
01-038A-4 R3 3×10 + 10 - 8 -
01-045A-4 R3 3×16 +16 - 6 -
01-062A-4 R4 3×25 + 16 - 4 -
01-073A-4 R4 3×35 + 16 - 2 -
01-061A-4 R5 3×25+16 3×35 4 -
01-072A-4 R5 3×35+16 3×50 2 -
01-087A-4 R5 3×35+16 3×70 2 -
01-105A-4 R6 3×50 + 25 3×70 1/0 -
01-145A-4 R6 3×95 + 50 3×120 3/0 -
01-169A-4 R7 3×120 + 70 3×150 250 MCM -
01-206A-4 R7 3×150 + 70 3×240 300 MCM -
01-246A-4 R8 2×(3×70+35) 2×(3×95) 2×2/0 -
01-293A-4 R8 2×(3×95+50) 2×(3×120) 2×3/0 -
01-363A-4 R9 2×(3×120+70) 2×(3×185) 2×250 MCM -
01-430A-4 R9 2×(3×150+70) 2×(3×240) 2×300 MCM -
3AXD00000586715.xls G
1)
The cable sizing is based on max. 6 cables laid on a cable ladder side by side, ambient temperature 30 °C,
PVC insulation, surface temperature 70 °C (EN 60204-1 and IEC 60364-5-52/2001). For other conditions,
size the cables according to local safety regulations, appropriate input voltage and the load current of the
drive. See also page
147 for the accepted cable sizes of the drive.
2)
Aluminum cables must not be used with frames R0…R3.
3)
In the USA, aluminum cables must not be used.