1000 V DC,
>
100 Mohm
U1-PE, V1-PE, W1-PE
ohm
M
3~
U1
V1
W1
PE
■
Measuring the insulation resistance of the brake resistor circuit
WARNING!
Obey the safety instructions of the drive. If you ignore them, injury or death,
or damage to the equipment can occur. If you are not a qualified electrical
professional, do not do installation or maintenance work.
1.
Stop the drive and do the steps in section
Electrical safety precautions (page 18)
before you start the work.
2.
Make sure that the resistor cable is connected to the resistor and disconnected from
the drive output terminals.
3.
At the drive end, connect the R+ and R- conductors of the resistor cable together.
Measure the insulation resistance between the conductors and the PE conductor
with a measuring voltage of 1000 V DC. The insulation resistance must be more
than 1 Mohm.
R-
R+
ohm
PE
1000 V DC,
> 1 Mohm
Grounding system compatibility check – IEC
This section is applicable to the IEC drive types.
■
EMC filter
The drive has an internal EMC filter as standard. You can install a drive that has the
internal EMC filter connected to a symmetrically grounded TN-S system (center-grounded
Electrical installation – IEC 65
Summary of Contents for ACS480-04-09A8-1
