ABB ACQ810 Firmware Manual Download Page 318

Page: 318 / 376

318 Fault tracing

2055

DEVICE CLEAN
(0x5080)

Maintenance counter alarm. See parameter group

44 Maintenance

Note:

Any maintenance counter alarm

sets bit 8 of

08.08

Alarm word4

2056

COOLING FAN
(0x5081)

2057

ADD COOLING
(0x5082)

2058

CABINET FAN
(0x5083)

2059

DC CAPACITOR
(0x5084)

2060

MOTOR BEARING
(0x738C)

2061

MAIN CONTACTOR
(0x548D)

2062

RELAY OUTPUT SW
(0x548E)

2063

MOTOR START COUNT
(0x6180)

2064

POWER UP COUNT
(0x6181)

2065

DC CHARGE COUNT
(0x6182)

2066

ONTIME1 ALARM
(0x5280)

2067

ONTIME2 ALARM
(0x5281)

2068

EDGE1 ALARM
(0x5282)

2069

EDGE2 ALARM
(0x5283)

2070

VALUE1 ALARM
(0x5284)

2071

VALUE2 ALARM
(0x5285)

2072

DC NOT CHARGED
(0x3250)

08.08

Alarm word4

The voltage of the
intermediate DC circuit has
not yet risen to operating
level.

Wait for the DC voltage to rise.

2073

AUTOTUNE FAILED
(0x8481)

08.08

Alarm word4

b10

Speed controller autotune
routine did not finish
successfully.

See parameter

23.20

PI tune mode

2074

START INTERLOCK
(0xF082)

08.08

Alarm word4

b11

No Start interlock signal
received.

Check circuit connected to DIIL input.

2076

TEMP MEAS FAILURE
(0x4211)

08.08

Alarm word4

Problem with internal
temperature measurement
of the drive.

Contact your local ABB representative.

Code

Alarm (fieldbus code),
other information

Cause

What to do

Summary of Contents for ACQ810
























































































































































































































































































































































































Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands

ABB ACQ810, Firmware Manual

Search results

Summary of Contents for ACQ810

Reviews:

Brands by name

Popular brands