manualshive.com logo in svg

ABB ACQ810, Firmware Manual

Share
Download
ABB ACQ810 Firmware Manual Download Page 250

250   Parameters

75.25

Drive start dly

Start delay for the pump that is directly controlled by the 
drive. This does not affect the starting of the auxiliary pumps.

WARNING! 

There must always be a delay set if the 

pumps are equipped with star-delta starters. The 
delay must be set longer than the time setting of the 

starter. After the pump is switched on by the relay output of 
the drive, there must be enough time for the star-delta starter 
to first switch to star and then back to delta before the pump 
is connected to the drive.

0…600 s

Start delay for drive-controlled pump.

1 = 1 s

75.26

Master speed acc

Defines the acceleration time in case the latest reference 
received by the drive is higher than the previous reference. 
This is likely to happen when the master status is passed on 
from one drive to another. The parameter sets the ramp-up 
time as seconds from zero to maximum frequency (

not

 from 

previous reference to new reference).
The parameter is effective only in the 

Copy of mstr

 and 

Master speed

 follower modes. See parameter 

75.03

 

Follower mode

.

0…1800 s

Acceleration time.

1 = 1 s

75.27

Master speed dec

Defines the acceleration time in case the latest reference 
received by the drive is lower than the previous reference. 
This is likely to happen when the master status is passed on 
from one drive to another. The parameter sets the ramp-
down time as seconds from maximum frequency to zero (

not

 

from previous reference to new reference).
The parameter is effective only in the 

Copy of mstr

 and 

Master speed

 follower modes. See parameter 

75.03

 

Follower mode

.

0…1800 s

Deceleration time.

1 = 1 s

76

76 MF communication

Communication configuration for applications consisting of 
multiple pumps with dedicated drives.

76.01

Enable MF comm

Enables/disables drive-to-drive communication through the 
D2D link.

Note:

 Drive-to-drive communication can only be enabled if 

the embedded fieldbus interface is disabled (parameter 

58.01

 

Protocol ena sel

 is set to 

Disabled

).

No

Drive-to-drive communication disabled.

0

Yes

Drive-to-drive communication enabled.

1

76.02

Pump node

Node number of the drive on the drive-to-drive link.

Notes:

•  Each drive on the link must have a unique node number.
•  If the drive is not given a priority class, the node number is 

also used in determining the starting order of pumps.

0…8

Node number.

1 = 1

76.03

Master enable

Determines (or defines a source that determines) if the drive 
is allowed to be master on the drive-to-drive link.

No

The drive can only be a follower on the drive-to-drive link.

0

Yes

The drive is allowed to be master on the drive-to-drive link.

1

Const

Bit pointer setting (see 

Terms and abbreviations

 on page 

109

).

-

Pointer

No.

Name/Value

Description

FbEq

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands