Home
/
ABB
/
ACQ810
/
Firmware Manual

ABB ACQ810, Firmware Manual

Share

Page: 139 / 376

ABB ACQ810 Firmware Manual Download Page 139

Parameters 139

10.17

Start enable

Selects the source for the Start enable signal.
1 = Start enable.
If the signal is switched off, the drive will not start or coasts to
stop if running.

DI1

Digital input DI1 (as indicated by

, bit 0).

1073742337

DI2

Digital input DI2 (as indicated by

, bit 1).

1073807873

DI3

Digital input DI3 (as indicated by

, bit 2).

1073873409

DI4

Digital input DI4 (as indicated by

, bit 3).

1073938945

DI5

Digital input DI5 (as indicated by

, bit 4).

1074004481

Const

Bit pointer setting (see

Terms and abbreviations

on page

-

Pointer

10.19

Start inhibit

Enables the start inhibit function. The function prevents drive
restart (i.e. protects against unexpected start) if
• the drive trips on a fault and the fault is reset,
• the run enable signal is activated while the start command

is active (see parameter

),

• control changes from local to remote, or
• external control switches from EXT1 to EXT2 or vice versa.
A new rising edge of the start command is needed after the
start inhibit has been activated.
Note that in certain applications it is necessary to allow the
drive to restart.

Disabled

The start inhibit function is disabled.

0

Enabled

The start inhibit function is enabled.

1

10.20

Start intrl func

Defines how the start interlock input (DIIL) on the JCU
control unit affects the drive operation.

Off2 stop

With the drive running:
• 1 = Normal operation.
• 0 = Stop by coasting. The drive can be restarted by

restoring the start interlock signal and switching the start
signal from 0 to 1.

With the drive stopped:
• 1 = Starting allowed.
• 0 = Starting not allowed.

0

Off3 stop

With the drive running:
• 1 = Normal operation.
• 0 = Stop by ramping. The deceleration time is defined by

parameter

. The drive can be restarted

by restoring the start interlock signal and switching the
start signal from 0 to 1.

With the drive stopped:
• 1 = Starting allowed.
• 0 = Starting not allowed.

1

No.

Name/Value

Description

FbEq

«
...
137
138
139
140
141
...
»

Summary of Contents for ACQ810

























































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands