ABB A175-M66 Operating Manual Download

Page: 31 / 150

Operation Manual / A170-M.. - A175-M..

3 Removal and installation / 3.2 Removing the turbocharger

HZTL4033_EN

Rev.H

July 2021

3.2

Removing the turbocharger

WARNING

Risk of tipping

If the turbocharger is not sufficiently supported or not supported at all dur-
ing removal and installation, it may tip over and cause severe injury to per-
sonnel or accidents resulting in fatalities.

Support the turbocharger at a suitable location.

Secure with lifting gear wherever possible.

If present: Loosen cable to speed sensor.

Disconnect all gas, air and lubricating oil pipes.

Fig. 12: Turbocharger suspension points

If present: Remove insulation segments on bearing casing and feet.

Attach lifting gear to the suspension lug of the bearing casing and through the boles on
the turbine-end foot.

Page

147

Summary of Contents for A175-M66





















































































































































Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands

ABB A175-M66, Operating Manual

Search results

Summary of Contents for A175-M66

Reviews:

Related manuals for A175-M66

Brands by name

Popular brands