ABB A175-M62 Operation Manual Download | Manualshive

Page: 91 / 148

background image

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.7 Removing the nozzle ring

© Copyright 2022 ABB. All rights reserved.

HZTL4033_EN

Rev.K

January 2022

9.7

Removing the nozzle ring

Removing the turbine diffuser

CAUTION

Risk of mixing up the press-off screws

In size A170-M, the press-off screw (90915) for pressing off the turbine dif-
fuser with thread size M18x1.0 can easily be mixed up with the press-off
screw (90901) with thread size M18x1.5. If the press-off screws are mixed up,
the thread of the turbine diffuser can be damaged.

u

Always use the appropriate press-off screws.

Fig. 44: Removing turbine diffuser 1

1. Remove screws (61069).

2. Using press-off screws (90915), press off turbine diffuser.

3. Fit guide plates (90328) with nuts (61037).

4. Screw in guide stud (90802).

Page

89

/

146

«
...
89
90
91
92
93
...
»

Summary of Contents for A175-M62





















































































































































Reviews:

No comments

Related manuals for A175-M62

Brand: Westerbeke Pages: 86

Brand: Nanni Pages: 32

Brand: Leb Electronics Pages: 24

Brand: Shindaiwa Pages: 48

General Pump 103166

Brand: Interpump Group Pages: 3

Brand: Sears Pages: 12

Brand: Dato Pages: 9

Featherweight 45

Brand: Seagull Pages: 25

Brand: RIEJU Pages: 63

Brand: Briggs & Stratton Pages: 112

Brand: Mitsubishi Heavy Industries Pages: 32

Brand: B&R Pages: 300

Brand: Asmo Marine Pages: 8

Brand: Applied Motion Products Pages: 2

Brand: Nanni Pages: 32

Brand: Orientalmotor Pages: 56

Brand: Controls Pages: 25

Brand: Parker Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands