ABB A175-M62 Operation Manual Download

Page: 20 / 148

Operation Manual / A170-M.. - A175-M..

2 Safety / 2.9 Turbocharger rating plate

HZTL4033_EN

Rev.K

January 2022

Explanations regarding the rating plate

The recommended replacement intervals and the corresponding operating limits are jointly
defined with the enginebuilder. This information is specific to the system.

Operation above the indicated values n

Bmax

, t

Bmax

can considerably shorten the recommended

replacement intervals. In such cases ABB recommends contacting the nearest ABB Tur-
bocharging Service Station.

Mmax

, t

Mmax

normally apply only when running at overload (110%) during trials on the engine

test bed. These limit values can also be permitted during operation for special applications.
Operation above n

Mmax

and t

Mmax

is not permitted.

Non-observance of the recommended replacement intervals increases the risk of unpredict-
able component failures.

Locations of the rating plates

Fig. 8: Locations of the rating plates

One rating plate (01) each is attached on the left and the right side of the foot of the tur-
bocharger.

On turbochargers with insulation supplied by ABB, at least one additional rating plate is at-
tached to the insulation of the gas outlet casing.

Page

146

Summary of Contents for A175-M62



















































































































































Search results

Summary of Contents for A175-M62

Reviews:

Related manuals for A175-M62

Brands by name

Popular brands

ABB A175-M62, Operation Manual

Search results

Summary of Contents for A175-M62

Reviews:

Related manuals for A175-M62

Brands by name

Popular brands