ABB A170-M66 Operation Manual Download | Manualshive

Page: 91 / 150

background image

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.7 Removing the nozzle ring

© Copyright 2021 ABB. All rights reserved.

HZTL4033_EN

Rev.H

July 2021

9.7

Removing the nozzle ring

Removing the turbine diffuser

CAUTION

Risk of mixing up the press-off screws

In size A170-M, the press-off screw (90915) for pressing off the turbine dif-
fuser with thread size M18x1.0 can easily be mixed up with the press-off
screw (90901) with thread size M18x1.5. If the press-off screws are mixed up,
the thread of the turbine diffuser can be damaged.

u

Always use the appropriate press-off screws.

Fig. 44: Removing turbine diffuser 1

1. Remove screws (61069).

2. Using press-off screws (90915), press off turbine diffuser.

3. Fit guide plates (90328) with nuts (61037).

4. Screw in guide stud (90802).

Page

89

/

147

«
...
89
90
91
92
93
...
»

Summary of Contents for A170-M66























































































































































Reviews:

No comments

Related manuals for A170-M66

Brand: Rato Pages: 65

Brand: Perkins Pages: 92

Brand: Lenze Pages: 36

Brand: Teryair Pages: 13

Brand: YS Pages: 2

Brand: Yanmar Pages: 214

Brand: Baldor Pages: 2

Brand: Yanmar Pages: 222

Brand: ActSafe Pages: 32

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: Ibi Pages: 2

Brand: B&R Pages: 98

Brand: LinMot Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands