ABB A170-M66 Operation Manual Download

Page: 110 / 150

Operation Manual / A170-M.. - A175-M..

9 Disassembly and assembly / 9.12 Axial clearance A after assembly

HZTL4033_EN

Rev.H

July 2021

9.12

Axial clearance A after assembly

WARNING

Physical hazards due to sharp edges on compressor wheel

The compressor wheel has sharp edges which can result in injury.

Wear safety gloves.

Wear safety gloves to protect against mechanical hazards.

The axial clearance (A) must be measured prior to removal and after installation of the cart-
ridge group.

CAUTION

Clearances outside the tolerance

Serious damage to engines or property can be caused by clearances outside
the tolerance and excessively worn parts.

Have the components assessed and, if necessary, replaced by an ABB Tur-
bocharging Service Station.

Fig. 64: Axial clearance

Product

Axial clearance A [mm]

A170-M

0.30 ... 0.61

A175-M

0.35 ... 0.69

Table 49: Axial clearance A

Measure and note axial clearance (A).

Page

108

147

Summary of Contents for A170-M66





















































































































































Search results

Summary of Contents for A170-M66

Reviews:

Related manuals for A170-M66

Brands by name

Popular brands

ABB A170-M66, Operation Manual

Search results

Summary of Contents for A170-M66

Reviews:

Related manuals for A170-M66

Brands by name

Popular brands