ABB A170-M66 Operation Manual Download

Page: 11 / 150

Operation Manual / A170-M.. - A175-M..

1 Introduction / 1.6 Symbols, definitions

HZTL4033_EN

Rev.H

July 2021

Definition of pictograms

The following pictograms can occur in this document. These point out actions that must be
taken in accordance with the meaning of the relevant pictogram.

Pictogram

Meaning

Tighten with specified torque

Tighten over specified tightening angle

Hand-tight, tighten without tools

Oil

Apply screw locking paste (e.g. Loctite)

Apply high-temperature grease

Apply other paste in accordance with specifications

Oil free, grease free and dry

Affix

Measure

Note

Visually inspect

Please note text for numbered work step.

See document

Dispose of in an environmentally compatible, professional way and in compliance
with locally applicable regulations.

Table 1: Definition of pictograms

Page

147

Summary of Contents for A170-M66





















































































































































Search results

Summary of Contents for A170-M66

Reviews:

Related manuals for A170-M66

Brands by name

Popular brands

ABB A170-M66, Operation Manual

Search results

Summary of Contents for A170-M66

Reviews:

Related manuals for A170-M66

Brands by name

Popular brands