ABB A170-M62 Page 73 Operation Manual Download

Page: 73 / 150

Operation Manual / A170-M.. - A175-M..

8 Troubleshooting / 8.2 Malfunctions during operation

HZTL4033_EN

Rev.H

July 2021

8.2

Malfunctions during operation

Lubricating oil pressure too low

WARNING

Danger of fire and explosion due to lubricating oil leaks

Leaking oil may ignite on hot surfaces. This can result in serious injuries to
personnel or fatal accidents.

Cordon off danger area.

Raise the alarm and, depending on the situation, stop the engine.

Seal the oil leak.

Soak up oil and dispose of in an environmentally compatible manner.

Wear safety gloves to protect against thermal hazards.

Possible causes

Remedy

Turbochar-
ger

Axial clearance of the rotor excessive

Contact an ABB Turbocharging
Service Station

Engine

Oil filter heavily contaminated

Clean

Oil pump in lubricating system defect-
ive

Check/replace

Manometer displays incorrectly

Replace manometer

Table 23: Malfunctions during operation – Lubricating oil pressure too low

Drop in speed

Possible causes

Remedy

Turbochar-
ger

Heavy contamination of the turbine
and/or nozzle ring

)

Damaged rotor components or bearing Contact ABB Turbocharging Service

Station

Engine

Defect on the connected cylinders in
pulse charging

Contact enginebuilder

Pipes

Defects, such as leaks, in the exhaust
gas pipes or charge air ducts

Repair

Table 24: Malfunctions during operation – Drop in speed

Increase in speed

Possible causes

Remedy

Turbochar-
ger

Light to medium contamination of the
turbine and/or nozzle ring (with 4-
stroke application)

) or contact an ABB Tur-

bocharging Service Station

Table 25: Malfunctions during operation – Speed increases

Page

147

Summary of Contents for A170-M62





















































































































































Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands

ABB A170-M62, Operation Manual

Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands