ABB A170-M62 Page 43 Operation Manual Download

Page: 43 / 150

Operation Manual / A170-M.. - A175-M..

5 Monitoring during operation / 5.1 Oil pressure, oil temperature

HZTL4033_EN

Rev.H

July 2021

Monitoring during operation

5.1

Oil pressure, oil temperature

Lubricating oil pressure

CAUTION

Assuring lubricating oil pressure

Serious damage to the engine or property can result from a missing or insuf-
ficient lubricating oil supply.

The lubricating oil pressure must be monitored during operation and the
necessary pressure assured at the oil inlet.

For monitoring the lubricating oil pressure, ABB Turbocharging recommends installing a
manometer "M". If the pressure is controlled electronically, the relevant signals should be
triggered at the warning and alarm values.

Fig. 23: Lubricating oil pressure measuring point

The permitted oil pressure ranges at measuring point M of the turbocharger are listed be-
low.

Status for operation

Pressure at measuring point M

oil, in

[bar]

Normal operation

1.3 ... 2.5

Engine start: Cold oil, admissible for max. 15 minutes

1.3 ... 5.0

Pre-lubrication

1.3 ... 2.5

Post-lubrication

1.3 ... 2.5

Long-term lubrication

0.2 ... 0.5

Warning signal: Temporarily admissible (<1 h )

1.0 ... 1.3

Alarm signal: Not permissible. Stop the engine immediately

< 1.0

Table 10: Oil pressure range

Page

147

Summary of Contents for A170-M62





















































































































































Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands

ABB A170-M62, Operation Manual

Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands