ABB A170-M62 Operation Manual Download

Page: 132 / 150

Operation Manual / A170-M.. - A175-M..

13 Spare parts / 13.1 Ordering spare parts

HZTL4033_EN

Rev.H

July 2021

Spare parts

13.1

Ordering spare parts

CAUTION

Spare part storage

All spare parts that were ordered together with the turbocharger must be
kept intact and ready for use.

Carefully clean any rusted parts and grease them.

Please quote the following data when making queries and ordering spare parts:

Turbocharger type

Serial number of the turbocharger

Designation and part number.

Spare parts can be ordered from any ABB Turbocharging Service Station.

If different model variants are not taken into account in this document, contact an ABB
Turbocharging Service Station.

Dispose of placed and unusable parts in an environmentally-friendly and professional
manner in accordance with the local regulations.

Dispose of the packaging of new parts in an environmentally-friendly and professional
manner in accordance with the local regulations.

Page

130

147

Summary of Contents for A170-M62





















































































































































Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands

ABB A170-M62, Operation Manual

Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands