ABB A170-M62 Operation Manual Download

Page: 123 / 150

Operation Manual / A170-M.. - A175-M..

10 Taking a turbocharger out of operation / 10.2 Locking the rotor

HZTL4033_EN

Rev.H

July 2021

10.2.2

Fitting the locking device

CAUTION

Turbocharger damage resulting from rotor unbalance

Removing the balancing screws from the compressor wheel will result in ro-
tor unbalance.

Only use free threaded holes to fit the lifting spigot (74027).

Remove the filter silencer or air suction branch (see chapter

Removing the air inlets

→

Fig. 74: Fitting the locking device

Product

Part number 72011

Part number 94006 / 94007

A170-M

170 Nm

25 Nm

A175-M

220 Nm

50 Nm

Table 56: Locking device tightening torque

1. Press off the spinner nose cone (25012) with the press-off screw (90917).

2. Remove two studs (72026) and three screws (72011) in the upper area.

3. Insert the lifting spigot (90441) into the compressor wheel.

Screw screws (94007) into the free threaded holes of the compressor wheel.

4. Position assembly/disassembly device (94003) with screws (72011) and lifting spigot

(90427).
Rotate compressor wheel in such a way that the holes in the lifting spigot (90427) corres-
pond with the holes in the assembly/disassembly device (94003).

5. Secure assembly/disassembly device (94003) to the lifting spigot (90427) with screws

(94006).

Page

121

147

Summary of Contents for A170-M62





















































































































































Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands

ABB A170-M62, Operation Manual

Search results

Summary of Contents for A170-M62

Reviews:

Related manuals for A170-M62

Brands by name

Popular brands