ABB 1ZSC902110-AAA Installation And Commissioning Manual Download

Page: 19 / 84

Installation and commissioning guide
1ZSC000563-AAF EN, REV. 4, 2021-06-23

4 Installation

4.1 Tools

Tool

Part number

Note

Lifting tool

PDV1909-1,-2,-4

Soft lifting slings

Pull-through cord

9760 669-A

With M8 terminal.

For assembly and disassembly of the
draw rod.

Torque wrench key for hex socket
screws, 16 mm (M10) and 13 mm (M8),
torque 20 to 40 Nm.

Wrench for hexagon head screws 45 mm
or adjustable wrench for 45 mm bolts
or larger.

For the test tap cover.

Hydraulic jack

9769 897-A

For removal, and installation of the
draw-rod system.

Box spanner

9760 669-B

For removal, and installation of the
draw-rod system.

4.2 Consumables

Item

Brand

Hitachi ABB part
number

Note

Oil based Vaseline

Fuchs

For treatment of contact surfaces. Does
not react with transformer oil.

Mobilgrease 28

MOBIL

Lubricates and protects metals against
corrosion. Protects rubber. Does not
react with transformer oil.

Molykote Multilub

Dow Corning

For lubrication of draw-rod threads and
bolts on the outer terminal.

Thread-locking fluid
grade 42

High strength thread-locking fluid,
permanent locking.

Thread-locking activator
grade 47

Activator for thread-locking fluid
grade 42.

Summary of Contents for 1ZSC902110-AAA





















































































Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands

ABB 1ZSC902110-AAA, Installation And Commissioning Manual

Search results

Summary of Contents for 1ZSC902110-AAA

Reviews:

Related manuals for 1ZSC902110-AAA

Brands by name

Popular brands