abaco systems PPC11A Hardware Reference Manual Download Page 77

Page: 77 / 159

Publication No. PPC11A-HRM/1

Control and Status Registers 77

5.13

NOR Flash Page Register (Offset 0x636)

Bits

Description

Default

Flash paging enable:
1 = Enabled

0 = Disabled

6 to 1

Reserved

000000

Flash page selected:

1 = Page 1

0 = Page 0

5.14

AXIS Registers

5.14.1 AXIS Timestamp Registers 0 to 5

These can be used to read the 48-bit timestamp. Reading register 0 latches the
current timestamp value into registers 1 to 5, so register 0 must always be read first.

AXIS Timestamp Register Offset Timestamp Value Bits

Default

0x648 7 to 0 (least significant byte)

0x00

0x649 15 to 8

0x00

0x64A 23 to 16

0x00

0x64B 31 to 24

0x00

0x64C 39 to 32

0x00

0x64D 47 to 40 (most significant byte) 0x00

5.14.2 AXIS Clock Frequency Register (Offset 0x64E)

This returns the AXIS master clock period in nanoseconds. When the PPC11A is
clock master, the frequency is 25 MHz (40 ns).

NOTE

Do not use this register when the PPC11A is an AXIS clock slave, as the frequency cannot be determined.

Software may use this register to determine if the AXIS timer is implemented (it

returns 0x00 if there is no AXIS timer).

Summary of Contents for PPC11A
































































































































































Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands

abaco systems PPC11A, Hardware Reference Manual

Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands