abaco systems PPC11A Hardware Reference Manual Download Page 105

Page: 105 / 159

Publication No. PPC11A-HRM/1

Control and Status Registers 105

5.42

EEPROM DIP Switch 1 Configuration Register 0 (Offset 0x6EA)

This register returns the state of the EEPROM DIP Switch 1 Register 0 when the
PPC11A was last reset. Only six bits are implemented.

Bits

Description

Default

7 & 6

Reserved

Load RCW from EEPROM:

1 = Load RCW from EEPROM

0 = Load RCW from main ROM/FPGA

RCW selection:
1 = Use RCW 'B'

0 = Use RCW 'A'

Write protect SSD:

1 = Write protect SSD

0 = Write enable SSD

2 to 0

PMC/XMC Site 1 Geographical Address:

101

= VIO is 5V

Others = VIO is 3V3

For XMC deployment, this is connected directly to the XMC;

for PMC deployment, this controls the PMC VIO voltage

5.43

EEPROM DIP Switch 1 Configuration Register 1 (Offset 0x6EB)

This register returns the state of the EEPROM DIP Switch 1 Register 1 when the
PPC11A was last reset. Only six bits are implemented.

Bits

Description

Default

7 & 6

Reserved

nvSRAM write protect:
1 = Write protect nvSRAM

0 = Write enable nvSRAM

Boot site swap (NOR Flash only):

1 = Swap main/alternate boot areas

0 = Do not swap main/alternate boot areas

GPIO7 usage:

0 = GPIO7 standard function

1 = Use GPIO7 as duplicate Boot Recovery link input

GPIO6 usage:

0 = GPIO6 standard function

1 = Use GPIO6 as duplicate Boot Alternate link input

GPIO5 usage:

0 = GPIO5 standard function

1 = Use GPIO5 as duplicate Flash Password Unlock link input

GPIO4 usage:

0 = GPIO4 standard function

1 = Reserved for GPIO4 special function

Summary of Contents for PPC11A
































































































































































Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands

abaco systems PPC11A, Hardware Reference Manual

Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands